Autel Maxisys Pro Vehicle Identification af angelababy Li

success of the recognition, the system will directly lead to find go into the

automobile diagnosis interface.

6 click [cancelled] out of hand as input.

The hand motion vehicle selection of the Autel Maxisys Pro

If the system fails to won the VIN code from inside the vehicle ECU , or the

VIN codes is unknown,

Then select in militaryvehicle selection function.

The hand motion vehicle selection generally has three ways:

Autel Maxisys Pro Hand

vehicle selection

The vehicle gradually select mode for menu guidance mode, only on screen as for a

series of choices can be even.

Every funeral selection after finishing will directly go into the next screen and

gradually reduce the vehicle selection

range until the accurate identification to the corresponding to the vehicle. Click on

the screen under the history []

button on the target back Hang back on a screen for re selection. Specific selectio

n procedures may be due to the vehicle is not

Same and hair.

1. hand motion input vehicleof the Autel Maxisys Pro
   

   
   

   By returning mode you can hand Mai input and save the concrete vehicle information,
   

   such as “Mai force chain control
   

   module part number,” calibration number “,” tag “, direct access to the vehicle
   

   electronic control module,
   

   save the gradually a selection of the time.
   

   How to input to the Ford vehicle Mai hand as an example
   

   1 click the Autel Maxisys Pro menu program. [] according to the diagnostic
   

   
   

   application menu button,
   

   open the “vehicle”. (Figure 4-1)
   

   2 Click the toolbar at the top of the [US] [all] button press ring.
   

   From the menu, select [3] vehicle Ford press button.
   

   4 vehicles from the options menu to select [input] hand motion of vehicle.
   

   (Figure 4-4) on the screen will display a series of confirmation information,
   

   
   

   click on the [is] to continue.
   

2. On the selection screen, select the following three funeral selected ares
   

   
   

3. that a – [Mai force chain control
   

   
   

   module part number], [calibration number], [label.
   

   6 [dynamic chain control module part number] are selected as an example,
   

   in the input box enter the accurate vehicle information.
   

   
   

   Autel Maxisys Pro
   

   OBD direct access
   

   
   

   Autel Maxisys Pro OBD access pattern
   

   In some cases, not supported by the Chu database, who quit vehicles with other
   

   functional properties,
   

   diagnostic technique not through normal channels of vehicle identification and
   

   communication is established.
   

   At this time, can directly access the OBD function for the general OBD II or EOBD
   

   
   

   test
   

   “Vehicle menu interface on the OBD II/EOBD vehicle diagnostic the quick access
   

   
   

   option (Figure 4-1).
   

   The option can be used to quickly check the fault codes, are found out by the fault
   

   indication lamp
   

   (MIL) lit the fault reason, in emissions obituary identification test before the check
   

   
   

   state monitor, repair
   

   verification is successful or not, and the implementation of other emissions related
   

   
   

   to the maintenance.
   

   OBD direct access option still can be used to test and diagnosis system, the
   

   
   

   database does not contain all the OBD II/EOBD compatible vehicle.
   

   The top of the screen button on the toolbar diagnosis operation is not other vehicle
   

   diagnostic procedures. The use of the same
   

   
   

   
   

   For mere information om vores produkt, kan du besøge vores officielle hjemmeside   www.getautel.com
   

   Or kontakt med vores salg direkte: Vores kontaktoplysninger er som følger:
   

   Skype cndiag01
   

   e-mail: [email protected]